Tag: 50982-12-2

Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.,50982-12-2

A mixture of [RuCl2(COD)]n (309 mg, 1.103 mmol), PCy3 (309 mg, 1.103 mmol) and Id (248 mg, 1.103 mmol) was stirred in toluene (10 ml) at 115 C for 48 h (in a KONTES pressure tube). After cooling, the brick colored precipitate was filtered on a filter frit, washed with Et20 (3 x 10 ml) and partially vacuum dried on the filter (vacuum pump). The residue was extracted from the filter frit with dichloromethane (6 >< 3 ml). The obtained solution was layered with Et20 (100 ml). Red-brown crystals were collected in few days (521 mg, 70%> yield). Elem. Anal: Calcd for (0461) C30H53Cl2N2PRuS (676.77): C, 53.24; H, 7.89; N, 4.14%. Found: C, 53.10; H, 7.95; N, 4.05%. 31P{1H} (162 MHz, CDC13, r.t.): delta 27.0 (s). 1H NMR (400 MHz, CDC13, r.t.): delta 0.78-3.90 (overlapped m, 47H), 5.57 (brs, 1H, NH), 7.22-7.53 (m, 3Eta), 8.10-8.30 (m, 2Eta). 13C{1H} (100.5 MHz, CDC13, r.t., selected without PCy3 carbon atoms): delta 46.7 (s, 1C), 46.8 (s, 1C), 48.5 (s, 1C), 52.3 (s, 1C), 54.2 (s, 1C), 67.2 (s, 1C), 128.2 (s, 2Cmeta, Ph), 129.4 (s, Cpara, Ph), 134.9 (s, 2Cortho, Ph), 137.8 (s, Cipso, Ph).

With the rapid development of chemical substances, we look forward to future research findings about Dichloro(cycloocta-1,5-diene)ruthenium(II)

Reference£º
Patent; LOS ALAMOS NATIONAL SECURITY, LLC; DUB, Pavel, A.; GORDON, John, Cameron; WO2015/191505; (2015); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.,50982-12-2

0.25 g of metal sodium was mixed with well dried tetrahydrofuran in a 100 ml flask whose inside had been substituted by nitrogen and cooled to -78 C. A solution of 1.3 g of trimethylsilyl cyclopentadiene dissolved in 30 ml of tetrahydrofuran was added dropwise to the above solution in a stream of nitrogen over 1 hour and heated to room temperature under agitation over 3 hours to obtain a tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium. Separately, 18 ml of a tetrahydrofuran solution (2.0 mol/l) of cyclopentadienyl sodium was prepared. Further separately, 5 g of dichloro(1,5-cyclooctadienyl)ruthenium was dissolved in 200 ml of well dried tetrahydrofuran in a 500 ml flask whose inside had been substituted by nitrogen. This solution was cooled to -78 C., and the above tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium and the above tetrahydrofuran solution of cyclopentadienyl sodium were added dropwise to the solution at the same time in a stream of nitrogen over 1 hour. The resulting solution was stirred at -78 C. for 3 hours and heated to room temperature under agitation over 12 hours. After the resulting solution was let pass through a neutral alumina column in an argon gas atmosphere to be purified and concentrated, it was separated and purified by a neutral alumina column again to obtain 0.23 g of trimethylsilyl cyclopentadienyl(cyclopentadienyl)ruthenium (yield rate of 4.3%).

With the synthetic route has been constantly updated, we look forward to future research findings about Dichloro(cycloocta-1,5-diene)ruthenium(II),belong ruthenium-catalysts compound

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belong ruthenium-catalysts compound,Dichloro(cycloocta-1,5-diene)ruthenium(II),50982-12-2,Molecular formula: C8H12Cl2Ru,mainly used in chemical industry, its synthesis route is as follows.,50982-12-2

1,2-closo-C2B10H12 (0.400 g, 2.77 mmol) was dissolved in degassed THF (35 mL). Na metal (0.300 g, 13.04 mmol) and naphthalene (ca. 15 mg) were added and the solution stirred overnight. The resulting dark green solution was transferred via a gas-tight syringe into a second Schlenk tube containing [RuCl2(COD)]x (0.650 g, 2.32 mmol) and a large excess of naphthalene. The resulting brown mixture was heated at reflux for 90 min then allowed to cool to room temperature. The brown mixture was filtered through a short silica column eluting with DCM to afford a brown solution, removal of solvent from which yielded a brown solid. This was further purified by column chromatography (1:2 DCM:40-60 petroleum ether), giving a yellow band, followed by preparative TLC (4:3 DCM:40-60 petroleum ether, Rf 0.55) yielding, as major product C12H20B10Ru requires C 38.59, H 5.40. Found: C 38.01, H 5.67%.

With the synthetic route has been constantly updated, we look forward to future research findings about Dichloro(cycloocta-1,5-diene)ruthenium(II),belong ruthenium-catalysts compound

Reference£º
Article; Scott, Greig; Ellis, David; Rosair, Georgina M.; Welch, Alan J.; Journal of Organometallic Chemistry; vol. 721-722; (2012); p. 78 – 84;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belong ruthenium-catalysts compound,Dichloro(cycloocta-1,5-diene)ruthenium(II),50982-12-2,Molecular formula: C8H12Cl2Ru,mainly used in chemical industry, its synthesis route is as follows.,50982-12-2

[HNEt3][7,8-nido-C2B9H12] (0.400 g, 1.71 mmol) was suspended in degassed ether (35 mL). n-BuLi (1.40 mL, 3.50 mmol) was added, giving a pale yellow suspension which was stirred under N2 for 1 h, then heated at reflux for 90 min. The resulting solution was filtered, and the ether removed in vacuo to give a yellow oily solid which was subsequently dissolved in degassed THF (35 mL). [RuCl2(COD)]x (0.560 g, 2.00 mmol) and a large excess of naphthalene were added to the THF solution. The resulting brown mixture was heated at reflux for 90 min, then allowed to cool to room temperature. The brown mixture was filtered through a short silica column eluting with DCM to afford a brown solution, removal of solvent from which yielded a brown solid. This was further purified by column chromatography (1:2 DCM:40-60 petroleum ether) giving a yellow band, followed by preparative TLC (2:1 DCM:40-60 petroleum ether). C12H19B9Ru requires: C 39.85, H 5.30. Found: C 39.87, H 5.53%.

With the synthetic route has been constantly updated, we look forward to future research findings about Dichloro(cycloocta-1,5-diene)ruthenium(II),belong ruthenium-catalysts compound

Reference£º
Article; Scott, Greig; Ellis, David; Rosair, Georgina M.; Welch, Alan J.; Journal of Organometallic Chemistry; vol. 721-722; (2012); p. 78 – 84;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

As a common heterocyclic compound, it belong ruthenium-catalysts compound,Dichloro(cycloocta-1,5-diene)ruthenium(II),50982-12-2,Molecular formula: C8H12Cl2Ru,mainly used in chemical industry, its synthesis route is as follows.,50982-12-2

Complex C-l was also prepared using [RuCl2(COD)]n as a precursor. Thus, a mixture of [RuCl2(COD)]n (309 mg, 1.103 mmol), PPh3 (289 mg, 1.103 mmol) and ligand Id (248 mg, 1.103 mmol) was stirred in toluene (10 ml) at 115C for 24 h in a KONTES pressure tube. After cooling, the resulting brick colored precipitate was filtered on a filter frit, washed with diethyl ether (3 x 10 ml) and vacuum dried to afford 494 mg of a light pink crude material (Found C, 53.43; H, 5.26; N, 4.08%). Recrystallization from hot THF, filtering and layering with diethyl ether, afforded burgundy crystals (261 mg, 32% yield as a THF solvate). Based on NMR analysis, these crystals represent a THF solvate of complex C-l. The crystals were found to lose solvent based on elemental analysis. Elem. Anal: Calc’d for C3oH35Cl2N2PRuS (658.63): C, 54.71; H, 5.36; N, 4.25%; Found C, 54.37; H, 5.66; N, 3.87%.

With the synthetic route has been constantly updated, we look forward to future research findings about Dichloro(cycloocta-1,5-diene)ruthenium(II),belong ruthenium-catalysts compound

Reference£º
Patent; LOS ALAMOS NATIONAL SECURITY, LLC; DUB, Pavel, A.; GORDON, John, Cameron; WO2015/191505; (2015); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.50982-12-2,Dichloro(cycloocta-1,5-diene)ruthenium(II),as a common compound, the synthetic route is as follows.

A solution of (tBu2PCH2CH2)2NH (1 .0 g, 2.77 mmol) was added to [RuCl2(cod)]n (0.775 g, 2.77 mmol) and the resulting suspension stirred for 4 hours underargon. This was followed by the addition of 4-methoxyphenyl isonitrile (368 mg,2.77 mmol) and the mixture refluxed for 15 hours under argon. It was cooled to room temperature and ether (40 ml) added, and the suspension stirred for 1 hour at room temperature. It was filtered, washed with ether and dried under vacuum. Yield = 1 .44 g. X-ray quality crystals were obtained by slow diffusion of ether into a CH2CI2 solution of the compound.

The synthetic route of 50982-12-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; HADEED, Gerald, S.; ABDUR-RASHID, Kamaluddin; (61 pag.)WO2018/193401; (2018); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, Dichloro(cycloocta-1,5-diene)ruthenium(II) is a ruthenium-catalysts compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Toluene (5 ml) was added to a mixture of (Ad2PCH2CH2)2NH (250 mg, 0.37 mmol) and [RuCl2(cod)]n (104 mg, 0.37 mmol) under argon and the mixture refluxed for 20 hours. The mixture was cooled to room temperature and4-methoxyphenyl isonitrile (49 mg, 0.37 mmol) added and the mixture refluxed for 12 hours under argon. It was cooled to room temperature and ether (40 ml) added. The pale brown solid was filtered, washed with ether and dried under vacuum. Yield = 0.18 g.

50982-12-2 Dichloro(cycloocta-1,5-diene)ruthenium(II) 11000435, aruthenium-catalysts compound, is more and more widely used in various.

Reference£º
Patent; HADEED, Gerald, S.; ABDUR-RASHID, Kamaluddin; (61 pag.)WO2018/193401; (2018); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.

The catalyst precursor, preferably [RuCI2(COD)]m (1 eq.) (COD = cis,cis-cycloocta-1 ,5 diene), 1 ,4-bis(diphenylphosphino)butane (1.0-1 .2 eq., preferably 1.0 eq.) and 2-picolylamine (1 .0-1.4 eq., preferably 1.225 eq.) were dissolved in one of the above mentioned solvents, preferably methyl isobutylketone (10-20 ml/g Ru-precursor, preferably 20 ml/g). The mixture was heated to reflux for 3 – 5 hours and then cooled to ambient temperature. The solid precipitate was filtered off and washed with the same solvent that was used for the reaction. A person skilled in the art can determine the cis-/trans- isomeric ratio by NMR. The diastereomeric ratios generated by this method are usually in the range of d.r. (diastereomeric ratio) >98% towards the cis isomer. The same results can be achieved starting with [RuCI2(dmso-KS)3(dmso-KO)], [RuCI2(dmso-KS)4]or [RuCI2(bicyclo[2.2.1 ]hepta- 2,5-diene)]m as precursor

As the rapid development of chemical substances, we look forward to future research findings about 50982-12-2

Reference£º
Patent; SYNGENTA PARTICIPATIONS AG; LOTHSCHUETZ, Christian; SAINT-DIZIER, Alexandre Christian; WO2014/166777; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.

The catalyst precursor, preferably [RuCI2(COD)]m (1 eq.), 1 ,4-bis(diphenylphosphino)butane (1 .0-1 .2 eq., preferably 1 .0 eq.) and 2- quinolinylmethylamine (1.0-1 .4 eq., preferably 1.225 eq.) were dissolved in one of the above mentioned solvents, preferably cyclohexanone (10- 20 ml/g Ru-precursor, preferably 20 ml/g). The mixture was heated at 130 C for 1 hour and then cooled to ambient temperature. The solid precipitate was filtered off and washed with the same solvent that was used for the reaction. A person skilled in the art can determine the cis-/trans- isomeric ratio by NMR. The diastereomeric ratios generated by this method are usually in the range of d.r. (diastereomeric ratio) >98% towards the cis isomer. The same results can be achieved starting with [RuCI2(dmso-KS)3(dmso-KO)], [RuCI2(dmso-KS)4]or [RuCI2(bicyclo[2.2.1]hepta-2,5-diene)]m as precursor

As the rapid development of chemical substances, we look forward to future research findings about 50982-12-2

Reference£º
Patent; SYNGENTA PARTICIPATIONS AG; LOTHSCHUETZ, Christian; SAINT-DIZIER, Alexandre Christian; WO2014/166777; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2, it is a common heterocyclic compound, the ruthenium-catalysts compound, its synthesis route is as follows.

11 g of trimethylsilyl chloride was dissolved in 30 mol of well dried tetrahydrofuran in a 300 ml flask whose inside had been substituted by nitrogen, and the obtained solution was cooled to -78 C. 100 ml of a tetrahydrofuran solution (2.0 mol/l) of cyclopentadienyl sodium was added dropwise to the above solution in a stream of nitrogen over 1 hour. The solution was stirred at -78 C. for 1 hour and returned to room temperature over 6 hours. A salt precipitated in the mixture solution was removed by filtration in a nitrogen atmosphere, and the residual solution was distilled to obtain 8 g of trimethylsilyl cyclopentadiene. 0.5 g of metal sodium was mixed with a well dried tetrahydrofuran solution in a 300 ml flask whose inside had been substituted by nitrogen, and the resulting solution was cooled to -78 C. A solution of 2.5 g of the above synthesized trimethylsilyl cyclopentadiene dissolved in 30 ml of tetrahydrofuran was added dropwise to the above solution in a stream of nitrogen over 1 hour and further heated to room temperature under agitation for 3 hours to obtain a tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium. Separately, 5 g of dichloro(cyclooctadienyl)ruthenium was dissolved in 200 ml of well dried tetrahydrofuran in a 500 ml flask whose inside had been substituted by nitrogen. This solution was cooled to -78 C., and the above synthesized tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium was added dropwise to the above solution in a stream of nitrogen over 1 hour. The resulting solution was stirred at -78 C. for 3 hours and returned to room temperature under agitation over 12 hours. After the solution was let pass through a neutral alumina column in an argon gas atmosphere to be purified and concentrated, it was separated and purified by a neutral alumina column again to obtain 0.9 g of bis(trimethylsilylcyclopentadienyl)ruthenium (yield rate of 13%).

As the rapid development of chemical substances, we look forward to future research findings about 50982-12-2

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI