Category: 50982-12-2

In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact.50982-12-2, Dichloro(cycloocta-1,5-diene)ruthenium(II) it is a common compound, a new synthetic route is introduced below., 50982-12-2

Separately, 200 ml of well dried tetrahydrofuran was fed to a 500 ml flask whose inside had been substituted by argon, and 5 g of dichloro(cyclooctadienyl)ruthenium was injected into the flask and well mixed with the above tetrahydrofuran to obtain a suspension. This suspension was cooled to -78 C. in a stream of argon, and 15 ml of the above synthesized tetrahydrofuran solution of trifluoromethyl cyclopentadienyl sodium was added dropwise to the suspension over 1 hour. The reaction mixture was further stirred at -78 C. for 3 hours and returned to room temperature under agitation over 12 hours. After the reaction mixture was let pass through a neutral alumina column in a stream of argon to be purified and concentrated, it was purified again by a neutral alumina column to obtain 0.2 g of bis(trifluoromethylcyclopentadienyl)ruthenium (yield rate of 30%)., 50982-12-2

As the paragraph descriping shows that 50982-12-2 is playing an increasingly important role.

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

General procedure: The following common procedure was followed for the synthesesof complexes 1-5: A mixture of the ligand (0.36 mmol) and Ru(1,5-cod)Cl2(0.36 mmol) was dissolved in dry ethanol (10 ml) and the resultingmixture was refluxed for 2 h. The reaction volume was concentratedto a third of its original volume and the suspension was keptat 4 C overnight to give brick red solid which was filtered off,washed with cold ethanol and then diethyl ether. The solid wasdissolved in chloroform and excess of n-hexane was added toinduce the precipitation of the brick red solid product.

The chemical industry reduces the impact on the environment during synthesis,50982-12-2,Dichloro(cycloocta-1,5-diene)ruthenium(II),I believe this compound will play a more active role in future production and life.

Reference£º
Article; Thangavel, Saravanan; Rajamanikandan, Ramar; Friedrich, Holger B.; Ilanchelian, Malaichamy; Omondi, Bernard; Polyhedron; vol. 107; (2016); p. 124 – 135;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

The catalyst precursor, preferably [RuCI2(COD)]m (1 eq.), 1 ,4-bis(diphenylphosphino)butane (1 .0-1 .2 eq., preferably 1 .0 eq.) and 2- quinolinylmethylamine (1.0-1 .4 eq., preferably 1.225 eq.) were dissolved in one of the above mentioned solvents, preferably cyclohexanone (10- 20 ml/g Ru-precursor, preferably 20 ml/g). The mixture was heated at 130 C for 1 hour and then cooled to ambient temperature. The solid precipitate was filtered off and washed with the same solvent that was used for the reaction. A person skilled in the art can determine the cis-/trans- isomeric ratio by NMR. The diastereomeric ratios generated by this method are usually in the range of d.r. (diastereomeric ratio) >98% towards the cis isomer. The same results can be achieved starting with [RuCI2(dmso-KS)3(dmso-KO)], [RuCI2(dmso-KS)4]or [RuCI2(bicyclo[2.2.1]hepta-2,5-diene)]m as precursor

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of Dichloro(cycloocta-1,5-diene)ruthenium(II), 50982-12-2

Reference£º
Patent; SYNGENTA PARTICIPATIONS AG; LOTHSCHUETZ, Christian; SAINT-DIZIER, Alexandre Christian; WO2014/166777; (2014); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

It is a common heterocyclic compound, the ruthenium-catalysts compound, Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2 its synthesis route is as follows.

Dichloro(1,5-cyclooctadiene)ruthenium (4.0 g, 0.014 moles), tricyclohexylphosphine (8.4 g, 0.030 moles), degassed triethylamine (2 mL), and degassed sec-butanol (60 mL) were combined in a pressure bottle under argon. The pressure bottle was purged with hydrogen gas, pressurized to 60 psi, and the mixture heated to 80 C. for 18 hours (the bottle was repressurized as needed to maintain 60 psi hydrogen). The reaction mixture was then allowed to cool down and the hydrogen gas was vented off. Degassed methanol (60 mL) was added to the orange slurry and the filtrate decanted off via stick filtration under argon to leave an orange solid in the bottle, which was washed with degassed methanol (60 mL). Degassed toluene (60 mL) was added to the orange solid and the orange slurry cooled to 0 C. Degassed 3-chloro-3-methyl-1-butyne (1.7 mL, 0.015 moles) was added dropwise via syringe at 0 C. The orange slurry progressively turned to a maroon slurry, while gas bubbled away. The mixture was stirred at room temperature for 2 hours after addition was complete. Ligand precursor [ 2] (18 g, 0.102 moles) was then charged and the mixture was heated to 80 C. and sparged with argon for 3 days (degassed toluene was added as needed). The brown slurry was allowed to cool to room temperature and a mixture of 30 mL methanol and 10 mL of concentrated hydrochloric acid was added in air with mixing. After stirring for 15 minutes at room temperature, the two phases were allowed to separate and the methanol phase was decanted off. Trituration with methanol (2¡Á50 mL) gave a solid, which was collected on a frit and washed with more methanol (2¡Á20 mL). The brown solid was then washed with hexanes (2¡Á20 mL) and dried to give [ 8] (5.1 g, 0.085 moles) in 61% yield.

50982-12-2, In the field of chemistry, the synthetic routes of compounds are constantly being developed and updated. I will also mention this compound in other articles.,50982-12-2 ,Dichloro(cycloocta-1,5-diene)ruthenium(II), other downstream synthetic routes, hurry up and to see

Reference£º
Patent; MATERIA, INC.; Pederson, Richard L.; Woertink, Jason K.; Haar, Christopher M.; Gindelberger, David E.; Schrodi, Yann; (13 pag.)US9504997; (2016); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

50982-12-2, In the next few decades, the world population will flourish. As the population grows rapidly and people all over the world use more and more resources, all industries must consider their environmental impact. Dichloro(cycloocta-1,5-diene)ruthenium(II), cas is 50982-12-2,the ruthenium-catalysts compound, it is a common compound, a new synthetic route is introduced below.

Next, 31.56 g of this (eta-1,5-cyclooctadiene)ruthenium(II) dichloride, 34.97 g of sodium carbonate, 28 mL of 2,4-pentanedione and 100 mL of N,N-dimethylformamide were placed in a nitrogen-flushed three-neck flask and stirred at 140 C. for 1 hour. Following reaction completion, the solution was cooled to room temperature, then alumina column chromatography (developing solvent: diethyl ether) was carried out. The resulting solution was concentrated, after which 120 mL of water was added and the solution was left at rest for 3 hours. The crystals that precipitated out were collected by filtration, and after being washed with water, were dried in vacuo. 46.53 g of bis(2,4-pentanedionato)(eta-1,5-cyclooctadiene)ruthenium(II) was obtained as an orangey-yellow solid. The yield was 94 wt %.

Chemical properties determine the actual use. Each compound has specific chemical properties and uses. We look forward to more synthetic routes in the future to expand reaction routes of Dichloro(cycloocta-1,5-diene)ruthenium(II), 50982-12-2

Reference£º
Patent; JSR Corporation; US2012/282414; (2012); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI