Brief introduction of 918870-76-5

As the paragraph descriping shows that 918870-76-5 is playing an increasingly important role.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.918870-76-5,Dichloro[1,3-bis(2,4,6-trimethylphenyl)-2-imidazolidinylidene][[5-[(dimethylamino)sulfonyl]-2-(1-methylethoxy-O)phenyl]methylene-C]ruthenium(II),as a common compound, the synthetic route is as follows.,918870-76-5

Example 103 Synthesis of Ru complex 6h The Ru complex (Zhan catalyst 2b, l.Ommol) and a new ligand 5h (1.5mmol) were dissolved in 20 mL of anhydrous DCM and reacted directly to form the desired Ru complex 6h in the preaence of CuCl (3.0mmol) in a 100 mL of three-neck flask filled with inert gas (Ar). The reaction mixture was stirred for 0.5 hr at room temperature. After complete, the reaction solution was filtered and purified by flask column. 378mg of yellow-green solid product 6h was obtained, yield: 52%. Ru complex 6h is confirmed by 1HNMR (400 MHz, CDC13): delta 16.52 (s, 1H, Ru=CH), 8.43 (s, 1H, N=CH), 8.10 (s, 1H), 7.46-7.22 (m, 2H), 7.73-6.96 (m, 8H), 4.19 (s, 4H, NCH2CH2N), 3.95 (s, 3H), 3.87 (s, 3H), 2.49 (s, 12H), 2.48 (s, 6H).

As the paragraph descriping shows that 918870-76-5 is playing an increasingly important role.

Reference£º
Patent; ZANNAN SCITECH CO., LTD.; ZHAN, James Zheng-Yun; WO2011/79439; (2011); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Brief introduction of 301224-40-8

As the paragraph descriping shows that 301224-40-8 is playing an increasingly important role.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.301224-40-8,(1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride,as a common compound, the synthetic route is as follows.,301224-40-8

Potassium 2,4,6-triphenylthiophenolate 2d (53 mg, 0.14 mmol) was transferred to a 25 mL Schlenk flask, followed by addition of 5 mL of THF under argon, and the mixture was stirred vigorously and heated at 55 C. Hoveyda-Grubbs second generation catalyst (82 mg, 0.13 mmol) dissolved in toluene (1 mL) was then added, and the mixture stirred at 55 C. for 2.5 h. The solvents were then removed in vacuo, and the product was redissolved in 6 mL Et2O. Following filtration, 3 mL of hexane was added, and the mixture cooled to -40 C., causing precipitation of impurities. After allowing solids to settle, the solution was filtrated, and the solvents removed in vacuo to yield the crude 4d complex as a green powder (50.7 mg, 42%). 1H NMR (400.13 MHz, C6D6): delta=14.50 (s, 1H), 7.80 (d, J=6.4 Hz, 2H), 7.47 (t, J=6.7 Hz, 2H), 7.42-7.34 (m, 2H), 7.31-7.21 (m, 3H), 7.11 (t, J=7.2 Hz, 3H), 7.08-7.00 (m, 3H), 6.99-6.90 (m, 3H), 6.87 (s, 2H), 6.79-6.60 (m, 4H), 6.15 (d, J=8.2 Hz, 2H), 4.15 (sept, J=6.1 Hz, 1H), 3.38-3.20 (m, 4H), 2.47 (s, 6H), 2.38 (s, 6H), 2.29 (s, 6H), 1.15 (d, J=6.1 Hz, 3H), 0.59 (d, J=6.1 Hz, 3H). (0132) 13C NMR (100.6 MHz, CD2Cl2): delta=276.55, 210.42, 153.68, 146.72, 138.75, 138.16, 131.23, 129.58, 129.12, 128.97, 128.75, 128.31, 127.87, 127.77, 127.50, 127.23, 127.01, 125.83, 122.65, 121.72, 113.38, 76, 15, 53, 87, 51, 98, 21.54, 21.25, 20.83, 19.92, 19.04. MS (DART), m/z: 928.27512 (M+H)+; calc. for C55H56OClN2SRu: 928.27671.

As the paragraph descriping shows that 301224-40-8 is playing an increasingly important role.

Reference£º
Patent; Bergen Teknologioverforing AS; Jensen, Vidar R.; Occhipinti, Giovanni; Hansen, Frederick Rosberg; US8716488; (2014); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Some tips on 20759-14-2

The synthetic route of 20759-14-2 has been constantly updated, and we look forward to future research findings.

20759-14-2, Ruthenium(III) chloride hydrate is a ruthenium-catalysts compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,20759-14-2

(4) Preparation of trans-3′-oxospiro[cyclohexane-1,1′(3’H)-isobenzofuran]-4-carboxylic acid A mixture of 4-hydroxymethylspiro[cyclohexane-1,1′(3’H)-isobenzofuran]-3’one (190 mg), chloroform (2.0 mL), acetonitrile (2.0 mL) and sodium phosphate buffer (pH6.5, 2.0 mL) was cooled to 0 C., to which sodium periodate (612 mg) and ruthenium(III) chloride n-hydrate (10 mg) were added and the mixture was stirred for 30 minutes. The reaction mixture was stirred together with 1N hydrochloric acid (2.0 mL) for 30 minutes and partitioned between water (50 mL) and ethyl acetate (50 mL). The organic layer was washed with saturated saline solution, dried over anhydrous Na2SO4 and then concentrated. The residue was purified by column chromatography on silica gel (chloroform/methanol=100/1) to give the subject compound (98.6 mg).

The synthetic route of 20759-14-2 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Banyu Pharmaceutical Co., Ltd.; US6803372; (2004); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Brief introduction of 301224-40-8

As the paragraph descriping shows that 301224-40-8 is playing an increasingly important role.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.301224-40-8,(1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride,as a common compound, the synthetic route is as follows.,301224-40-8

General procedure: A mixture of fluorinated acid silver salt 6 (2.2eq.) and dichlororuthenium(IV) complex 5 (1.0eq.) was first dried under vacuum (13Pa) at room temperature for 1h. Dry dichloromethane (5mL) was added and the resulting mixture was stirred at room temperature for 3h in the dark. The solids were filtered off and washed with dry dichloromethane (2mL). Evaporation of the solvent afforded the product 7-9.

As the paragraph descriping shows that 301224-40-8 is playing an increasingly important role.

Reference£º
Article; Babun?k, Mario; ?im?nek, Ond?ej; Ho?ek, Jan; Ryba?kova, Marketa; Cva?ka, Josef; B?ezinova, Anna; Kvi?ala, Jaroslav; Journal of Fluorine Chemistry; vol. 161; (2014); p. 66 – 75;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Analyzing the synthesis route of 10049-08-8

As the paragraph descriping shows that 10049-08-8 is playing an increasingly important role.

10049-08-8, Ruthenium(III) chloride is a ruthenium-catalysts compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,10049-08-8

Example 13 Synthesis of (3S)-3-(1,3-benzodioxol-5-yl)-3-[({1-[2-oxo-3-(phenylmethyl)-1(2H)-pyridinyl]cyclohexyl}carbonyl)amino]propanoic Acid Step One: To a solution of 3-benzylpyridine (1.65 g, 9.77 mmol) in acetone (3.5 mL), 1-chloro-2,4-dinitrobenzene (2.00 g, 9.56 mmol) was added and the mixture was refluxed overnight. The mixture was cooled to room temperature, diluted with acetone and the solvent was decanted from the precipitate. The crude solid was washed with acetone (2 times) and diethyl ether (1 time), decanting each time to give 37(3.57 g, 100percent) as a gray solid. Step Two: To a solution of 1-amino-1-hydroxymethylcyclohexane (0.45 g, 3.5 mmol) in n-butanol (8.75 mL), solid N-(2,4-dintrophenyl)-3-benzylpyridinum chloride (37, 1.23 g, 3.3 mmol) was added. The resulting solution was heated to reflux for 2.5 days under a nitrogen atmosphere. The mixture was cooled, diluted with water and filtered. The filtrate was basified with concentrated NH4OH (2 mL) and extracted with ethyl acetate. The aqueous layer was concentrated to dryness to give 38(0.56 g) as a yellow oil which was used without further purification. Step Three: To a solution of crude 38(0.56 g, 3.5 mmol theoretical) in water (10 mL), a solution of potassium ferricyanide (3.3 g, 10 mmol) in water (15 mL) was added dropwise via an addition funnel over 30 minutes at 0¡ã C. A solution of KOH (0.76 g, 13.5 mmol) in water (5 mL) was then added over 30 minutes. Toluene (10 mL) was added and the solution was stirred for one hour at 0¡ã C. The layers were separated, and the aqueous layer was extracted again with toluene. The combined extracts were dried over Na2SO4 and filtered and the filtrate was concentrated under reduced pressure. The residue was chromatographed on silica gel, eluding with 7:13 hexanes:ethyl acetate to give 39(20 mg, 1.9percent, two steps.) Step Four: To a suspension of 39(20 mg, 0.068 mmol) in aqueous KOH (1M, 0.70 mL) potassium persulfate (0.073 g, 0.270 mmol) and ruthenium (III) chloride (1 mg, catalytic) and THF (0.25 mL) were added. The mixture was stirred for 1 hour and extracted with dichloromethane. The aqueous layer was acidified and extracted with ethyl acetate (3 times). The ethyl acetate extracts were combined, dried over MgSO4 and filtered. The filtrate was concentrated under reduced pressure to give 40(0.0148 g, 70percent) as a tan solid. (3S)-3-(1,3-Benzodioxol-5-yl)-3-[({1-[2-oxo-3-(phenylmethyl)-1(2H)-pyridinyl]cyclohexyl}carbonyl)amino]propanoic acid was prepared from 40according to the procedures described in Example 1. 1H NMR (400 MHz, CD3SO2CD3): delta 1.40 (m, 4H), 1.68 (m, 2H), 2.04 (m, 2H), 2.60 (d, J=7.0 Hz, 2H), 3.67 (d, J=15.2 Hz, 1H), 3.72 (d, J=15.2 Hz, 1H), 5.12 (m, 1H), 5.95 (m, 2H), 6.19 (t, J=7.0 Hz, 1H), 6.74 (dd, J=7.8, 1.4 Hz, 1H), 6.76 (d, J=7.8 Hz, 1H), 6.90 (d, J=1.4 Hz, 1H), 7.10 (d, J=5.8 Hz, 1H), 7.20 (m, 5H), 7.57 (d, J=8.4Hz, 1H), 7.66 (dd, J=7.7, 1.8 Hz, 1H).

As the paragraph descriping shows that 10049-08-8 is playing an increasingly important role.

Reference£º
Patent; Biediger, Ronald J.; Dupre, Brian; Hamaker, Linda K.; Holland, George W.; Kassir, Jamal M.; Li, Wen; Market, Robert V.; Nguyen, Noel; Scott, Ian L.; Wu, Chengde; Decker, E. Radford; US2003/199692; (2003); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Application of 2,3-Dihydrobenzo[b][1,4]dioxine-5-carboxylic acid

With the rapid development of chemical substances, we look forward to future research findings about 301224-40-8

The ruthenium-catalysts compound, cas is 301224-40-8 name is (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride, mainly used in chemical industry, its synthesis route is as follows.,301224-40-8

General procedure: A mixture of fluorinated acid silver salt 6 (2.2eq.) and dichlororuthenium(IV) complex 5 (1.0eq.) was first dried under vacuum (13Pa) at room temperature for 1h. Dry dichloromethane (5mL) was added and the resulting mixture was stirred at room temperature for 3h in the dark. The solids were filtered off and washed with dry dichloromethane (2mL). Evaporation of the solvent afforded the product 7-9.

With the rapid development of chemical substances, we look forward to future research findings about 301224-40-8

Reference£º
Article; Babun?k, Mario; ?im?nek, Ond?ej; Ho?ek, Jan; Ryba?kova, Marketa; Cva?ka, Josef; B?ezinova, Anna; Kvi?ala, Jaroslav; Journal of Fluorine Chemistry; vol. 161; (2014); p. 66 – 75;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Application of Thiomorpholine

With the rapid development of chemical substances, we look forward to future research findings about 301224-40-8

The ruthenium-catalysts compound, cas is 301224-40-8 name is (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride, mainly used in chemical industry, its synthesis route is as follows.,301224-40-8

Hoveyda-Grubbs second generation catalyst (150 mg, 0.24 mmol) and potassium 2,4,6-trimethylbenzenethiolate 2c (59 mg, 0.31 mmol) were transferred to a 25 mL Schlenk flask, followed by addition of 5 mL of benzene and 1 mL of THF under argon. Then the mixture was stirred vigorously at 20 C. for 30 min. During this time the color of the mixture turned from light green to dark green. The reaction mixture was filtered, and the volume of the filtrate reduced to about 3 mL. Hexane (15 mL) was then added to the dark-green solution under stirring to precipitate the ruthenium complex 4c as a dark green powder (98.5 mg, 55.3%). Further purification was accomplished by dissolving the product in benzene and precipitating with hexane. Crystals for X-ray crystal structure determination were grown by slow diffusion of pentane to a concentrated solution of 4c in fluorobenzene, see FIG. 13 and Table 5. (0127) 1H NMR (400.13 MHz, CDCl3): delta=14.89 (s, 1H), 7.20 (m, 1H), 7.09 (s, 2H), 7.05 (s, 2H), 6.78-6.73 (m, 2H), 6.57 (br s, 1H), 6.14 (d, 1H), 5.99 (br s 1H), 4.13 (m, 4H), 3.95 (sep, 1H), 2.62 (s, 6H), 2.54 (s, 6H), 2.42 (s, 6H), 2.28 (br s, 3H), 2.03 (d, J=6.1 Hz, 3H), 0.92 (d, J=6.1 Hz, 3H), 0.81 (br s, 3H). 13C NMR (100.6 MHz, CD2Cl2): delta=269.24, 211.58, 151.83, 145.22, 139.26, 138.89, 138.82, 138.16, 133.95, 129.72, 129.39, 127.54, 127.30, 122.75, 122.40, 114.07, 75.20, 53.84, 52.25, 21.40, 21.20, 21.17, 20.79, 19.89. (0128) A corresponding ORTEP-style diagram of 4c is shown in FIG. 13. Selected geometrical parameters: Ru1-C16=1.842 , Ru1-S1=2.338 , Ru1-Cl1=2.375 , Ru1-O1=2.236 , Ru1-S1-C1=107.66, Cl1-Ru1-S1=159.61.

With the rapid development of chemical substances, we look forward to future research findings about 301224-40-8

Reference£º
Patent; Bergen Teknologioverforing AS; Jensen, Vidar R.; Occhipinti, Giovanni; Hansen, Frederick Rosberg; US8716488; (2014); B2;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Downstream synthetic route of 50982-12-2

50982-12-2 Dichloro(cycloocta-1,5-diene)ruthenium(II) 11000435, aruthenium-catalysts compound, is more and more widely used in various.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.50982-12-2,Dichloro(cycloocta-1,5-diene)ruthenium(II),as a common compound, the synthetic route is as follows.,50982-12-2

General procedure: The following common procedure was followed for the synthesesof complexes 1-5: A mixture of the ligand (0.36 mmol) and Ru(1,5-cod)Cl2(0.36 mmol) was dissolved in dry ethanol (10 ml) and the resultingmixture was refluxed for 2 h. The reaction volume was concentratedto a third of its original volume and the suspension was keptat 4 C overnight to give brick red solid which was filtered off,washed with cold ethanol and then diethyl ether. The solid wasdissolved in chloroform and excess of n-hexane was added toinduce the precipitation of the brick red solid product.

50982-12-2 Dichloro(cycloocta-1,5-diene)ruthenium(II) 11000435, aruthenium-catalysts compound, is more and more widely used in various.

Reference£º
Article; Thangavel, Saravanan; Rajamanikandan, Ramar; Friedrich, Holger B.; Ilanchelian, Malaichamy; Omondi, Bernard; Polyhedron; vol. 107; (2016); p. 124 – 135;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

Downstream synthetic route of 301224-40-8

301224-40-8 (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride 11763533, aruthenium-catalysts compound, is more and more widely used in various.

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.301224-40-8,(1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride,as a common compound, the synthetic route is as follows.,301224-40-8

General procedure: A mixture of fluorinated acid silver salt 6 (2.2eq.) and dichlororuthenium(IV) complex 5 (1.0eq.) was first dried under vacuum (13Pa) at room temperature for 1h. Dry dichloromethane (5mL) was added and the resulting mixture was stirred at room temperature for 3h in the dark. The solids were filtered off and washed with dry dichloromethane (2mL). Evaporation of the solvent afforded the product 7-9.

301224-40-8 (1,3-Dimesitylimidazolidin-2-ylidene)(2-isopropoxybenzylidene)ruthenium(VI) chloride 11763533, aruthenium-catalysts compound, is more and more widely used in various.

Reference£º
Article; Babun?k, Mario; ?im?nek, Ond?ej; Ho?ek, Jan; Ryba?kova, Marketa; Cva?ka, Josef; B?ezinova, Anna; Kvi?ala, Jaroslav; Journal of Fluorine Chemistry; vol. 161; (2014); p. 66 – 75;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI

New learning discoveries about 50982-12-2

50982-12-2 Dichloro(cycloocta-1,5-diene)ruthenium(II) 11000435, aruthenium-catalysts compound, is more and more widely used in various.

50982-12-2, Dichloro(cycloocta-1,5-diene)ruthenium(II) is a ruthenium-catalysts compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated,50982-12-2

11 g of trimethylsilyl chloride was dissolved in 30 mol of well dried tetrahydrofuran in a 300 ml flask whose inside had been substituted by nitrogen, and the obtained solution was cooled to -78 C. 100 ml of a tetrahydrofuran solution (2.0 mol/l) of cyclopentadienyl sodium was added dropwise to the above solution in a stream of nitrogen over 1 hour. The solution was stirred at -78 C. for 1 hour and returned to room temperature over 6 hours. A salt precipitated in the mixture solution was removed by filtration in a nitrogen atmosphere, and the residual solution was distilled to obtain 8 g of trimethylsilyl cyclopentadiene. 0.5 g of metal sodium was mixed with a well dried tetrahydrofuran solution in a 300 ml flask whose inside had been substituted by nitrogen, and the resulting solution was cooled to -78 C. A solution of 2.5 g of the above synthesized trimethylsilyl cyclopentadiene dissolved in 30 ml of tetrahydrofuran was added dropwise to the above solution in a stream of nitrogen over 1 hour and further heated to room temperature under agitation for 3 hours to obtain a tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium. Separately, 5 g of dichloro(cyclooctadienyl)ruthenium was dissolved in 200 ml of well dried tetrahydrofuran in a 500 ml flask whose inside had been substituted by nitrogen. This solution was cooled to -78 C., and the above synthesized tetrahydrofuran solution of trimethylsilyl cyclopentadienyl sodium was added dropwise to the above solution in a stream of nitrogen over 1 hour. The resulting solution was stirred at -78 C. for 3 hours and returned to room temperature under agitation over 12 hours. After the solution was let pass through a neutral alumina column in an argon gas atmosphere to be purified and concentrated, it was separated and purified by a neutral alumina column again to obtain 0.9 g of bis(trimethylsilylcyclopentadienyl)ruthenium (yield rate of 13%).

50982-12-2 Dichloro(cycloocta-1,5-diene)ruthenium(II) 11000435, aruthenium-catalysts compound, is more and more widely used in various.

Reference£º
Patent; JSR Corporation; US2006/240190; (2006); A1;,
Highly efficient and robust molecular ruthenium catalysts for water oxidation
Catalysts | Special Issue : Ruthenium Catalysts – MDPI